Jump to content

Onomatopoeia

Members
  • Content Count

    157
  • Joined

  • Last visited

Everything posted by Onomatopoeia

  1. Onomatopoeia

    Pod HD500X causing crash in Reaper

    Like the title says, Windows 10 kept crashing multiple times today when I tried to record someting i Reaper. It just went to blue screen. VERY ANOYING. I´ve seen simular threads like this but without a fix. How do I fix this? I´ve reinstalled Line 6 drivers aswell as Windows for sound. No results. The pod HD500 is my only recording interface.
  2. Onomatopoeia

    Input gain and very high output bass guitar.

    I also have a G&L Bass (L2000) with insanely high output and ran into the same issue. There are 3 ways to solve this: 1. Lower the pickups from the strings 2. Turn down the volume on your bass 3. Either use the aux in or the return in (both have a 10k ohm) if you only have the LT version (like me). I opted for lowering the pickups a bit ( around 3/16" on bass side and a bit less on the treble side - unfettered, open strings). This cleans things up a whole bit. I now run it through the Normal input with pad on and it's sounds great. I did however also try the return 1 set to line level but found that this doesn't do that much if your pickups are to close to the strings to begin with. Does your bass clip anything while you have no amp or pedal blocks in your patch? If not, you're probably just clipping some of the blocks later in your signal chain. You could also try to place an eq block before the amp block set to - 6db to simulate using a active input on your amp block. I haven't tried this last part but I think it should work!
  3. Onomatopoeia

    Merge block levels and panning law

    I've asked in the Facebook group and read some threads over here about the topic but some things about it still confuses me, so here we go again. Is there any panning law by default in the Helix while using Y splits or AB splits followed by a merge block? At what dB? Is the signal lowered att the split or at the merge block? I'm using a patch for my bass that has a y split in the beginning with some distortion blocks on path 1b, and no blocks on path 1a, followed by a merge block, some comp, mod and lastly a single amp block and a cab. I use this setup to "blend" the distortions with my clean bass tone before hiting the amp block. But something sounds "off" while doing this compared to just putting all the blocks on a single path. I do understand how panning does work and that merging two mono signals results in a boost of 3db, two stereo signals in a 6 db boost, etc. Allthough i compensate by cutting the output block of the merge block I still end up by a signal that sounds either slightly boosted or with to little gain hitting the amp block. The settup that seem to be working the best is to use a Y split with L+R hard panned to either side and then both panned center at the merge block + a -3db compensation at the merge blocks output gain. Even by doing this you can clearly hear a difference when moving fxs like a comp block before or after the split+merge. Am I missing something? I do not have the dist blocks in path 1b on all the time and I want my blocks to get the same amount of signal after the split/merge as if I wasn't usinging parallel paths. Is this even possible?
  4. Onomatopoeia

    Merge block levels and panning law

    Helix core 3.0?
  5. Onomatopoeia

    Merge block levels and panning law

    Can somebody from L6 please shed some light on this?
  6. Onomatopoeia

    Input impedance of return 1 and 2?

    Anybody that knows what the impedance is for return 1 and 2 on the Helix LT?
  7. Onomatopoeia

    Input impedance of return 1 and 2?

    Thank you. So pluging in an active bass in one of the returns (set to line level) would be the equivalent to using the aux input? I got the LT version.
  8. Onomatopoeia

    Input impedance of return 1 and 2?

    Let's hope someone from L6 answers!
  9. Onomatopoeia

    Helix FAQ

    I´d also like to know that!
  10. Onomatopoeia

    Merge block levels and panning law

    Unfortunately, there's nothing over there (atleast that I could find) on the topic.
  11. Onomatopoeia

    Merge block levels and panning law

    Yeah I think I've read them all. The problem is that it only seems like people are guessing. I've read in one of the threads that there actually is a 3db pan law, but it doesn't seem that way since you still end upp with a slightly boosted signal after the merge. I know that this probably won't be an issue if you put the merge LAST in the path, but it will cause problems if you merge before gain sensitive blocks. LINE 6 really should clarify this so people can get the most out of their units.
  12. Onomatopoeia

    Helix LT FAQ

    I´d like to know this aswell!
  13. Onomatopoeia

    Pod HD500X causing crash in Reaper

    Yeah your´re probably right. Check out that link for optimizing Windows for audio that I posted above!
  14. Onomatopoeia

    Windows 10 Last Version & Drivers Crash DAW's

    Hi. I had the same problem and I think I finaly got it to work out! Check out my thread: "Pod HD500X causing crash in Reaper"
  15. Onomatopoeia

    Pod HD500X causing crash in Reaper

    Good tips! I THINK I finaly got it to work (it hasn´t crashed yet)! I did reinstall windows and followed some of the steps in the comments above. I also used this guide for optimizing Windows 10 for audio!: https://support.focusrite.com/hc/en-gb/articles/207355205-Optimising-your-PC-for-Audio-on-Windows-10 It´s very important to turn of all the features running in the background of windows. Also, set your comp to flight mode or turn of the network card if you can!
  16. Onomatopoeia

    Pod HD500X causing crash in Reaper

    Thank you
  17. Onomatopoeia

    Pod HD500X causing crash in Reaper

    Any body knowing something else that might solve this? Scary that there's a lot of these threads around here centering on L6 and seemingly without a real solution...
  18. Onomatopoeia

    Pod HD500X causing crash in Reaper

    Yeah it really sucks. I have the same proplem with Audacity aswell. I sure hope it´s the Pod´s fault in some way because I´m really thinking about selling it and getting me something better as of now. I just want to be sure it´s not the fault of my laptop so I´m in the same boat again after going through the hassle of selling and bying new gear! And I really like my tone that I´m getting now from the pod :(
  19. Onomatopoeia

    Pod HD500X causing crash in Reaper

    An update.... Right now I have tried EVERYTHING that you guys recomended and more, (except buying a new USB cable!) and I still get BSOD.... I even uninstalled my antivirus! I really think it has something to do with the pod. After playing around in reaper for a few mins (without bsod) I saved and closed Reaper down. Then a few mins later when I unplugged the USB from the pod a got a BSOD. Then the next time I got a BSOD was when I restarted Windows and went in to change audio settings in control panel - BSOD... Another thing is when I have project open in Reaper, if i click on something outside Reaper (a message that mail that shows up on the right for example) the tracks in reaper shows as "offline" until I click on Reaper again... And right now I´m jaming along to some songs on Youtube without a problem (not counting that you can get BSOD if unplugging before closing Youtube). Really wierd and VERY frustrating problem...
  20. Onomatopoeia

    Pod HD500X causing crash in Reaper

    Yeah, but my pc doesn´t seem to find any problem. Thx anyways!
  21. Onomatopoeia

    Pod HD500X causing crash in Reaper

    Hm might be worth to invest in a slightly longer USB cabel anyways... No I have not tried to disable the integrated audio as the POD is automaticly set as the default device. Will check it out tomorrow!
  22. Onomatopoeia

    Pod HD500X causing crash in Reaper

    I don´t think that MS Fix it is working on Windows 10! There´s only one acount on my computer and I´m the admin. I havn´t tried another computer, but I do have acces to one and will try that.... Thanks for the help though, and yeah... this is insanity...
  23. Onomatopoeia

    Pod HD500X causing crash in Reaper

    No I haven't tried that one yet.. I read a post you made in some older thread on the same issue, where You mentioned something about disable the Pod HD as the main soundcard and only use it for Reaper. How do I disable it so only Reaper Is using it? The only programs I use while connected to my laptop is Reaper and Google, for playing along to songs on YouTube (not att the same time!)
  24. Onomatopoeia

    Pod HD500X causing crash in Reaper

    After analysing the dumps from the blue screens (had some help from a tech) I´m getting mostly this: ntoskrnl.exe hardware_ram ntkrnlmp.exe And I allways get this: DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT What to do now?
×