-
Posts
651 -
Joined
-
Last visited
Everything posted by dboomer
-
Gain Questions (Tx and P180)
dboomer replied to lostinsound's topic in XD-V Digital Wireless Microphones
NO problem using third party antennas. There is a white paper posted somewhere on the Line 6 site that shows a bunch of them. Also we had quite good luck with the RF Venue CP24 helical antenna. It has about 9 dB of gain and many times will work better than the P180/360 antennas because their line amps will up the noise floor. So even though you get a little less gain you get a better signal to noise ratio which is more likely to be a gating factor. -
The input can handle 6vac p-p. So a gain of 20dB. depends on what the starting signal is. But the answer is likely yes.
- 2 replies
-
- onboard preamp
- relay
-
(and 2 more)
Tagged with:
-
Variax digital cable and Relay G70/G75
dboomer replied to MarkSabbath's topic in Relay Digital Wireless
You cannot. L6 link operates at a much higher frequency than Relay can handle. -
M20D - Pan Outputs?
dboomer replied to timothybhewittesq's topic in StageScape Mixer / StageSource Speakers
I can think of a couple of work arounds. You could assign one monitor bus to be post fader and use that to control your backline speaker independently from your front speaker Or you could assign all of your inputs to a group. Then you could use the pan control for the group to change the ratio of left to right on the mains outputs. -
Using stock antennas with extended cables?
dboomer replied to jojodeluxe's topic in XD-V Digital Wireless Microphones
Your plan may work and it may not. The best solution would be to add paddles to the Line 6 wireless and split them apart by 3 meters or more and raise them up in the air to 2-3 meters. -
Using stock antennas with extended cables?
dboomer replied to jojodeluxe's topic in XD-V Digital Wireless Microphones
If you cannot 100% control all wifi in your venue you should not be running in RF2 mode. Switching to RF1 should go a long way towards solving your problems. How close is the tablet to the receiver's antennas? A minimum of 3 meters should be observed. This looks like you should be using paddle antennas. Using the supplied whip antennas will only go so far. You are limited to using 3 meters of antenna cable so you can't move them much. -
Extending the L6 link range
dboomer replied to nickinfrance's topic in StageScape Mixer / StageSource Speakers
Unfortunately AES repeaters do not work. L6 link is not an AES/EBU signal. It is at a much higher data rate, hence the shorter max distance. -
Control M20D with Android tablet?
dboomer replied to tochiro's topic in StageScape Mixer / StageSource Speakers
Android is not "class compliant" and it is also much slower. Each Android manufacturer has their own version of the operating system. That means you have to create a number of apps and that drives costs. -
M20D - Can't move input?
dboomer replied to timothybhewittesq's topic in StageScape Mixer / StageSource Speakers
I tried your setup and what I found is that you have used a preset for input 3 that cannot ever be moved to 13-16 because it requires more DSP than is available on the line inputs. That preset (kick drum) will only operate in 1-12. The preset that you used for input 2 is one of those Arne mentioned in post #2 (AC gtr direct) and that one can be moved to any input. -
WiFI interference with Behringer X-Air
dboomer replied to TiffinMusic's topic in XD-V Digital Wireless Microphones
If you upgraded the firmware in your V70 units to v2.x and ran in RF2 mode you could probably get one wi-fi channel to operate unaffected as well. Alternately you could run your mixer at 5Ghz using an external router. -
Check out the new G70. Should be on store shelves very soon. http://line6.com/relay-g70-g75/
-
One way to look at it I guess. OTOH, which $199 digital wireless IS upgradable at all? :D
-
G50 relay dropout every 15 seconds or so
dboomer replied to AdamBradders's topic in Relay Digital Wireless
This is a new unit and it has never worked well? It probably is defective and switching it out should take care if the problem. -
It's the same part.
-
M20D - Can't move input?
dboomer replied to timothybhewittesq's topic in StageScape Mixer / StageSource Speakers
You have deleted from the setup what was previously in 13/14? Can you backup your mixer and email me the file? dboomer@line6.com -
Mic & Reciever compatibility question
dboomer replied to Reason413's topic in XD-V Digital Wireless Microphones
Yes it will work fine but you will get the 6 available channel limit of the receiver. -
You need to be certain that both units are operating in the same RF mode. New units default to RF2 mode but can be switched to RF1 mode. Units more than 2 years old may only operate in RF1 mode (unless they have been flashed to the updated firmware. Usually RF1 is the best mode for stage bands. Check the FAQ for details.
-
Relay G50, dropouts, weak RF signal receive
dboomer replied to Noogard's topic in Relay Digital Wireless
It would seem that some problem has developed with the receiver. The only other things you could try before sending it to the service center would be to try different antennas or to flash the receiver with new firmware. -
Because it is not intuitive it makes it difficult to understand. But when your IEM'antennas are very close to your G90's antennas they ARE IN THE SAME BAND. You must move one set of antennas to the other to get reliable operation.
-
M20D - Can't move input?
dboomer replied to timothybhewittesq's topic in StageScape Mixer / StageSource Speakers
Are you trying to move stereo presets? They will lock out the other half. -
Voice mic volume was suddenly very low
dboomer replied to tochiro's topic in StageScape Mixer / StageSource Speakers
Not enough information to guess the cause. Could be a hardware issue, could have been the mic cable or possibly you accidentally brushed the touchscreen and unknowingly changed a parameter. It is likely that it is not a hardware problem as reloading a setup corrected the problem. A note about using scenes/setups ... I frequently make copies as I go along. I start with "My Scene" and as the night progresses I save any updates as "My Scene2", "My Scene3", etc. I blow them out at the end of a gig but this way you are less likely to have to start over should something like this happen. -
Yes, the monitors will receive a full range signal (unless you purposely change it using the parametric EQ in the monitor bus master).
-
That's a job for your DeEsser (which is a special dynamic EQ preset really)
-
g30 transmitter battery indicator going from blue to green
dboomer replied to shagtones's topic in Relay Digital Wireless
Assuming the batteries are good (hope you've tried a couple of sets) and making contact properly then it sounds like a hardware issue. You should open a service ticket and get it checked out. Use "contact us" link at bottom of the page.