hurghanico

Yes, you can.. What silverhead said is perfectly valid when it comes to editing patches directly on the device. As for the behavior of the Editor, it temporarily keeps in memory (until you close the program) all the edits made to all the patches present read from the device. However, as long as you do not use the SEND command of the Editor the original patches present in the POD are never modified, so if you close the editor without using the above command, you will find then all the patches in the device exactly as they were previously. The main difference between the behavior of the POD (alone) and the Editor is that in the POD (with no Editor running) when you select and edit a patch its data are copied to 1 volatile buffer, and changes to the current patch are made permanent only if you use the SAVE command, otherwise they are lost and the original patch data remains unaltered. As soon as a new patch is selected, its data is copied into the only existing volatile buffery, thus taking the place of the previously selected patch data. The editor, on the other hand, does not have the " just 1 single volatile buffer" limit, but temporarily stores any changes made to all the patches present read, and in any case the original patches contained in the device are not touched in any way until the SEND command is used. Tip: If while using the Editor you edit a patch and at some point want to get it back in the Editor to how it was originally, simply select the patch in the Editor and use the RECEIVE SELECTED command, and the original untouched patch data will be read again from the device. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

In general the cab/speaker/mic chosen represents more than 50% of the sound of an amp.. the external IRs (very similar in concept to the cab/speaker/mic models already included in Helix which are also derived from IRs) are useful simply to have a greater number of different cabs/speakers/mics to choose from. When you choose an internal or external (IR) cab/speaker/mic you do it only according to the sound you are looking for when you pair it with a certain amp, in general there is no IR that is better than another, they are all different, but there are certainly those you would personally prefer based on the resulting final sound when you finally hear them. the problem is that you cannot know in advance (unless you have already experienced it) what the final result will be when you match a certain IR to a certain amp (plus there are several other variables involved, but let stop here). So any IR needs to be tested personally to see if based on your taste/needs it really fits well in a certain pairing. If you want you can read a short explanation about IRs given by Ownhammer (well known IRs maker) here: https://www.ownhammer.com/tutorials/general/ _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

Giving examples of patches for different uses/scenarios IMO would not be very useful, as the best thing to do is to build them on the spot by yourself based on your instrumentation, way of playing, and the context in which you are at the moment. Eg: - recording of a track to be inserted among others of other instruments, where therefore a certain equalization helps you to hear your own instrument and all the others in a distinct way, and obviously the equalization changes according to the song and the instruments already present. - live at high volume, the general equalization of the various channels of the various instruments is up to the sound engineer (if any). as for the guitarist's live sound (compared to the low volume sound at home or in the studio) it is often necessary to boost the mid frequencies (or lower the bass and treble a little and turn up the volume which is more or less the same thing ) to ensure that the guitar signal does not get lost among the other instruments and is well present in the overall mix (for the scientific explanation of why you need more mids at high volume see The Fletcher and Munson Curve). _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

No.. AFAIK there is not.. but you can still open the HD500X Edit program, load your POD patches and see your settings and parameters from there.. the editor works also offline, ie with no device connected _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

I found also the following http://www.keithhollandguitars.com/line-6-xps-ab-direct-box.html# but it is not clear how old the announcement is and whether it is still valid _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

Maybe I've been lucky but after 2 seconds google search I found this: Line 6 XPS-AB Variax Cabled Power Kit However, before buying a new XPS A/B box, if I were you, I'd check the power supply Put new batteries in your 600 _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

When you switch guitar models via Helix patches the devices communicate via the VDI cable and respective ports, that's why I suggested checking them. But anyway I suspect that also the problem above (like that of piezos) depends on the fact that your instruments are often or always in an exceptionally humid environment such as for example it could be a basement or an underground garage, etc.. I strongly advise against keeping any digital or non-digital musical instrument in an exceptionally humid environment, otherwise they are bound to age prematurely and malfunction over time. New generations of instruments would also suffer exactly the same way due to humidity, but initially they would work better only because they have not yet had time to wear out prematurely. If you really can't do it otherwise you should at least use a dehumidifier in the room where you keep and use your instruments. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

At the top of this page you can see a couple of Line6 announcements regarding POD/MacOS compatibility _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

Have you tried another VDI cable?.. or ethernet cable? Are the pins of the modeler and guitar VDI sockets still well aligned? _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

I have a 700 but I believe there are no substantial differences with the 600 regarding piezos and modeling. Some time ago I had a problem with the piezo of a string, one of the 3 low strings, i.e. in the area where the palm of the hand comes into contact with the bridge in particular for palm muting, with consequent transfer of sweat and fragments of skin to the underlying elements. Following the advice of a friend from this forum, I gently extracted the piezo from its housing (IIRC I used adhesive tape to grab it), and I cleaned with isopropyl alcohol both the piezo and housing elements which must necessarily create a perfect electrical contact between them, which with accumulation of dirt over time is lost. Moreover, before putting the piezo back into its housing, I turned it 180 degrees, to offer a new side of it to the string. Since then it has always worked perfectly. I have not replaced any piezos to date, and have been using the guitar every day for years. maybe the model selector is dirty or worn and if so a light sprinkle of de-oxid or a drop of isopropyl alcohol along the pot shaft could help.. or maybe at some point the knob of the models was removed and then reinserted back not exactly as before .. even though the knob stops at predefined points when it moves, the potentiometer (shaft) below can move in a linear way and each model has a small range area (a few degrees) of it for its selection, so if the above knob (moving in steps) is not positioned in such a way that its stop points correspond to the center of that linear range of the pot for each model, and maybe the stop points are too close to the border between one model area and another, the selection does not work as it should. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

Actually what's called input 1 in the DAW corresponds to the LEFT side of the dual mono/stereo output signal of the POD, and what's called input 2 in the DAW corresponds to the RIGHT side of the above signal. To keep the 2 sides of the POD dual mono/stereo output signal separate and independent (ie not mixed together) no mono blocks (mono FX or amp) in the chain should be placed before the split point and after the mixer block (because they would create 2 copies of the same processed signal on both sides L and R), and in the mixer block the path A PAN control should be set to the LEFT and the path B PAN control to the RIGHT. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

I may have read more than the the OP meant, but his following sentence seems rather unambiguous to me: My interpretation of the above sentence (but it could be wrong) and reasoning: What is connected to the USB? ..........The POD........ Where are the PC speakers connected? .........presumably to the PC (probably built in)........ Can they play the sound from the POD / USB? .........Impossible......... it is "normal behavior"...... It is not an advanced concept, but a trivial mistake that newbies sometimes do _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

If the PC speakers are separate or detachable best thing to do is to connect them to the POD outputs or headphone output. If instead the PC speakers are not separate or detachable much probably they can play only the sound coming from the PC integrated audio interface, which means that in order to hear also the POD sound through them, the POD outputs (usually the USB digital signal is not selectable as an input by the integrated AI) or headphones output must be connected to the audio input of the PC and activated through the PC audio control panel/mixer. I would strongly suggest the first much effective and simpler solution, so you can record and playback everything through the USB by using the POD as audio interface (much better than any PC integrated AI) which finally converts digital back to analog, and connect any speakers/monitors/headphones directly to it. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

You can bet safely on it! _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

Hammond patch _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

Yes! Power Supply/Battery Specs and FAQ _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

First of all, writing in this forum is not useful to talk to the Line6 team, but only with other users. That said, even if you do manage to speak to someone of the Line6 team (e.g. by phone or via support ticket) I believe they will never be willing to provide you with the protocol data sheet. Perhaps for your purpose it might be a better idea to analyze the program and its source code created by a forum member a while ago to convert presets from one format to another of the various POD HD series models: Pod Hd Tone Conversion Utility and see what useful information you can get. Who knows, maybe the author himself could give you some tips. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

Unless device malfunctions occur firmware flashing is a one-time-only procedure, and there will be no new firmwares for the POD in the future. So why not use any PC to do just that? _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

POD HD500 compatible tones matching "limelight" How to Play Limelight by RUSH on Guitar - taught by Alex Lifeson _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

.. in addition to what has been already said you might be interested also in one of the Yamaha (still Line6 under the hood) THR series all in one solution modeling amps (speakers included) perfect also for low volume playing and else, very easy to use. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

Les Paul and other humbucker PU equipped guitars are not only hotter than single coil PU equipped guitars, but their low end is so big that if not lowered in some way can easily cause unwanted bad distortion in the next thing in the chain. The POD models in particular are very sensitive (maybe too much) to strong bass frequencies in the input signal therefore I suggest to reduce their level as needed with the available controls to get a better balanced tone and a cleaner attack. If instead the problem is a kind of dissonant ghost notes that overlap the normal ones as they decay, the issue can be solved by lowering the amp models HUM parameter. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

Try the Mesa Boogie Dual Rectifier Solo (Cali Tread), the amp used by Limp Bizkit, Linkin Park, Incubus, Korn, Metallica etc. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

I doubt very much that a firmware flashing procedure could physically damage a mainboard in any way. Unfortunately I don't know of any other ways to properly install the firmware on that device, but for me the problem is just that, and a Line6 technician would know how. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

The name of your problem is: Ground Loop Noise. If you are using a notebook try to disconnect it from the mains and use it on battery (probably the noise will disappear), or find and use a Ground Loop isolator/killer. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips

The Cali diamond treadplate has never been modeled for the POD HD series, but has been included among all the stock models of the POD X3, and buying the Metal Shop model pack it can also be added to the POD XT and the POD Farm plugin. You can find it listed in the X3 model gallery: https://line6.com/data/6/0a060b316ac34f0593be902d6/application/pdf/POD X3 Model Gallery - English ( Rev B ).pdf Here is the description: 2001 Diamond Plate Based on* Channel 3 of a Mesa/Boogie® 2001 Triple Rectifier® Solo Head. _______________________________________________________________________________________________________________________________________________________________________ All about POD HD500/X help and useful tips