jandrio

Check out these: http://blog.line6.com/2013/2061/ u can find many more if u search 4 "hd500 acoustic" videos... Of course u can use a real acoustic, or even a JTV guitar.

Since u didn't notice much of a boost using the Variax and u are using the volume pedal all the time, then I do not see any other solution than the studio eq or the fx loop. In either case u must "consume" one FX slot.

Why don't u use the exp-1/2 to control the amp(s) channel volume(s)? Set min @say 70% and max @100%, so whenever u need the xtra boost, just hit the toe pos, otherwise use the heel pos. No slot "consumed", only prerequisite u do not use the exp-1/2 as wah.

Check out these: http://line6.com/support/topic/4513-best-way-of-getting-a-dual-guitar-sound-ie-thin-lizzy/?do=findComment&comment=29562 http://line6.com/customtone/tone/217427 Also consult the "MasterPuppetSolo" factory preset on the HD500.

From translator: "I also have problems with the volume, it does not settle in Exp-1 could help me?" @juan1987: Por favor, publique en Inglés. Please post in english.

For exporting a list with preset names, try this one: http://line6.com/support/topic/5196-export-list-from-l6-edit/?do=findComment&comment=34157

1st picture: tube drive applied over BOTH paths 2nd picture: tube drive applied ONLY over path A, path B carries pure guitar signal. c attached abstract from "POD HD500 Advanced Guide v2.10 - English ( Rev A )", page 6-2. "With the Amp in Pre, as shown above, the single amp feeds both Paths A & B."

Connect thru usb 'n use POD HD EDIT application. Dowlnoad from here

Never mind. Here is n other one of our Zep covers. http://www.mediafire.com/listen/n0xqnq1flaf7qdv/The+Pure-Ages+Rock+and+Roll+cover.mp3 This one was recorded with a 1968 tele and a Fender Prosonic custom shop combo.

Sorry abt that. Should I change & post another cover?

Solo is INTENTIONALLY interpreted this way, just to differentiate. Hear carefully, I reassure u it is absolutely "metronomed". rgds/john

@StairwayToHeaven: Check out our last cover bearing ur name: Guitar solo part recorded with JTV69s+HD500.

If u use only one XLR, u must place a noise gate as the last FX in the chain in order to sum up to mono, otherwise u will lose one part of the signal. Set the noise gate @100/0 (leaves the tone "untouched"). 4 further reading check out this one: http://line6.com/support/topic/2033-pod-hd-500-500x-new-routing-schematics/ ps Alternatively, try using HD500 left XLR to line input AND HD500 right XLR to to mic input, as GTLazer suggested. In this case u get full signal L+R, so u do not need the abv stated noise gate.

Check out this one:

Try this one: http://foobazaar.com/podhd/toneGuide/troubleshooting#fizz

Also make sure NOT to turn ur volume level at 0, cause it forces the JTV in2 sleep mode... Abstract from Variax Reflash and Software Update Instructions

http://foobazaar.com/podhd/toneGuide/ampTone#noiseGates

...and c it on customtone perhaps?

Verify that ur java vm is latest version (I believe latest version is 7 something).

If u want to change model-PUs during playing, u cld implement it via defferent presets on the HD500. As far as the LOCK setting is concerned, u cld use it in a situation where both signals (ie Variax AND Variax mags) are fed in2 the HD500. In this case the switch+tone effects only the mag sound and not the model sound. Abstract from "POD HD500 Edit Pilot's Guide v2.0 - English ( Rev A )" page 4-2:

I believe it's the CTRL key not the ALT key for copying... Abstract from the "POD HD500 Edit Pilot's Guide v2.0 - English ( Rev A )" page 6-3: -

Yes u can. However output mode must be either "direct" or "combo/power amp". On the HD500 u cannot have different settings per output jack (1/4 - xlr's). Proposed configuration with JTV+HD500 as follows: Connect the JTV via VDI to the HD500 and use only the XLR’s out to the PA for ALL sounds (acoustic + electric) with “Studio direct†output mode. Run the 1/4 out of the HD500 to amp’s effects loop return, thus using the amp only as stage monitor. In case u don't have a JTV, just connect thru the 1/4 guitar input.

Cld u pls attach here a zip file with the JTV+HD500 settings 4 the Kashmir patch?

It seems that u r in2 a "ground loop" symptom. Does ur "buffered" AB box have a ground lift switch? c attached img. Check out this one. Alternatively, u cld just feed the L output of ur POD to one amp and the R to the other. In any case, u shld take in2 consideration the ground loop.

I guess either way u have to do at least ONE SINGLE move, ie; 1. Power off the monitors, OR 2. Set the Amp/Line switch in the middle position (assuming silverhead's "trick" is a go. So there is no way out but to to do repeatedly either action 1 or action 2 above...