phil_m

Not to be annoying about it, but double check... Every time I've seen this error, it's been because the person was using an outdated version of Edit. Note that the number that shows up on the bottom of the screen in Edit is the firmware version on the connected unit, not the version of Edit. For that you have to look at Help>About. EDIT: I just noticed you said .hir files... Is your Stomp registered to your account? It has to be in order for you to use files you bought from the Marketplace. Also, make sure you're signed into your Line 6 account on HX Edit.

Make sure you’re running the latest version of HX Edit.

How are you monitoring the Stomp?

I mean all the delays in the recording are from the Dual Delay model.

It sure seems like something isn’t right if you think the Stomp’s delay are dark compared to the Echosystem... I owned the Echosystem, and I certainly would not have considered it a bright sounding delay. The Transistor Tape model is a bit darker because it’s a tape echo, but the Dual Delay certainly shouldn’t be. You might want to try the Vintage Digital model. With the sample rate and bit depth parameters all the way up, it’s actually one of the most pristine delays in the Helix. As far as the Dual Delay, I recorded this a few years ago, and all the delays are the Dual Delay.

No, see my post above... Each footswitch on the Helix can be set to be "Momentary" or "Latching" in the Bypass Assign screen. This behavior is independent of what you do in the Command Center. Thinking back, I know I've done this before with the CC Toggle command.

No, I'm saying select the CC Toggle command and set the function of the switch itself to be Momentary instead of Latching. It's been awhile since I've messed with this, but I believe you might need to have a block assigned to that footswitch in order to set it to momentary. But once you do that, you can set its behavior to momentary or latching in the Bypass Assign Screen. So just assign a dummy block, like a Gain block to that footswitch and then set the command.

Yes, when set to latching it would work that way, but if you set to Momentary and Toggle, I believe it will send the Dim value as soon as you release the footswitch.

Can't you do that with the CC Toggle? I believe the Toggle can be set up to be momentary as well, so it goes to the lit value while you hold the footswitch down and then back to the dim value with the footswitch released.

The PP2+'s 9V outs don't have enough capacity to power the Stomp, even if you summed them all together.

The Stomp won’t send MIDI Sysex messages even with the MIDI Out set to Thru, and that’s how the Boss editor is communicating with the ES-8.

Yes, that’s to be expected. The backing tracks are probably normalized, and maybe mastered, so they’ll be a lot louder than the processed guitar signal coming from the Stomp.

Any advice I give on here is free, man... Glad you seemed to have worked it out!

Phantom power won't damage the Helix, but it can attenuate and/or make the output from the XLR outs sound bad. You should have phantom power turned off for the channel you're connecting the Helix to.

Actually, Line 6 customer service had a very good reputation anymore. Go look at the Digital Modeling forum on The Gear Page or check out the Facebook groups for the various products. Line 6 goes out of their way to help people. As far your issue, the CS guy is correct. Matte finishes are prone to get shiny in areas where your resting your arm against them and such. I have a Gibson ES-335 that has a satin finish (similar to a matte, just not as diffuse), and the same thing happens. There are areas where the finish gets worn and becomes shiny.

First thing to do is go to Global Settings>MIDI/Tempo>MIDI PC Send and set it to "Off". This setting controls whether or not the default PC message associated with each LT preset is sent out automatically when you load a preset. I think this is what's messing you up. Beyond that, there are two basic ways the Helix sends MIDI commands. You can either assign MIDI commands to footswitches or there are six Instant Commands per preset (Instant Commands can also send commands on a snapshot per snapshot basis). When you go into the Command Center, you'll see the footswitch icons. Those, as you probably guessed, represent each footswitch in Stomp Mode. The lightning bolt icons represent the six Instant Commands. If you only want to change channels on your amp using MIDI PCs, you only need to use one Instant Command. Set it to the MIDI channel your amp is set to and select the PC you want to send. That PC will then be sent when you load that preset. It's as simple as that. Like I said, though, I think the automatic PC send feature is probably the thing messing you up.

After you select the footswitch as the controller, go to Bypass/Controller Assign tab. Then click on the line on the left hand side of the screen that says "Variax - Variax Model - Footswitch #". Then you'll see the parameter bars for the min and max settings show up. I think there's a bug in HX Edit regarding this as the Preset Variax Model doesn't show in the pulldown menu on the Bypass/Controller Assign tab. But selecting it from the list of all controllers on the left is an easy workaround.

It would all be much easier with snapshots. But I suppose it depends on what you're envisioning. You can assign the Variax model parameter to a footswitch, though. You don't need to mess with a MIDI CC. Just right click on the Preset Variax Model parameter and select the footswitch you want to assign it to. You can set a different model for the min and max settings of the footswitch. Then the footswitch will let you toggle between two models.

You mean alternate tunings with a standard guitar? I don't see that ever happening, to be honest. Polyphonic pitch shifting will probably happen, but real-time pitch shifting for each string, well, that would be quite a feat.

What are you trying to as far as transferring the tone? You shouldn't have to register it in order to use any of the relevant software. Honestly, at this point, registering it really isn't going to get you anything.

You need to set the delay time to a note value subdivision. On the unit itself, simply press the knob under the delay time and you'll see the value change from milliseconds to note values. Once you do that, you can turn the knob to select whatever note value you want. That note value will be tied to the tap tempo.

Is "Tx MIDI Clock" turned off under Global Settings>MIDI/Tempo on the HX Effects? With MIDI over USB it's very easy to get a MIDI feedback loop, and I suspect that's what's happening.

Not from Line 6. You can always get one printed for yourself if you want.

Well, that is the intended functionality per the manual. Setting Preset Mode to Momentary takes you back to Stomp Mode. I agree with you, though, having it take you back to the Mode you were previously in would seem to be more useful. I actually suggested that to DI in an email awhile ago.