Line6Tony

We discovered that there is a serial number mismatch on a group of Helix Rack units that will affect their ability to be registered. If your unit's serial number includes 6603-6607, please register the serial number label that is attached on the unit, not the serial number label attached to the box. If you run into further registration issues, please contact our support team with a support ticket at www.Line6.com/support/tickets. We apologize for any inconvenience you may experience.

Please be aware that downloaded tones, patches and presets that were created by other users have the potential to be corrupted and not work correctly on the target device. Firewall/Antivirus/Internet security applications, Internet/video accelerators and proxy servers, among other things, can be causes of trouble with downloaded files. If your device freezes, a rule of thumb is to back up your custom patches, reset the unit to its factory state, ensure the unit does not freeze while in this state, then load your patches one by one, testing after each load to determine which patch is faulty. Otherwise, please contact our Customer Support team at www.Line6.com/support/tickets. Please be prepared to supply your backup file so that we can investigate your case further.

We have seen a variety of behaviors where the app is indicating a good connection to the hardware, but it is not actually communicating with the hardware. Music will still stream from the device, but the app will not connect to the hardware. This can happen following a firmware update over Bluetooth or during any app connection. In order to avoid or resolve this, we suggest the following: Android For AMPLIFi 75/150/TT, first try a factory reset on the AMPLIFi on to clear out any of it's stored Bluetooth settings. To perform a factory reset, press and hold the master volume knob and the 'tone' button as you power on the unit. turn the amp off and press and hold both the 'Tone' and Master Volume down as you power on the amp. Keep holding them both down until you see the LED's around the Master Volume light up. For AMPLIFi FX100, turn the pedal off and press and hold both the 'Tap' and Master Volume down as you power on the pedal. Keep holding them both down until you see the display light up with '01'. Next, on your mobile device, make sure that the AMPLIFi Remote app is fully closed and not running in the background. Within your mobile device Bluetooth settings you will need to delete any entries for AMPLIFi if possible. Press and hold the Bluetooth button on the AMPLIFi for 2 seconds until it begins to flash. It should then shortly appear within your mobile device Bluetooth settings, tap on it to re-pair. Try again to launch AMPLIFi Remote app, tap the menu button located in the upper left of the app and look to see if it shows that your AMPLIFi is 'connected' or not. iOS For AMPLIFi 75/150/TT, first try a factory reset on the AMPLIFi on to clear out any of its stored Bluetooth settings. To perform a factory reset, press and hold the master volume knob and the 'tone' button as you power on the unit. Turn the amp off and press and hold both the 'Tone' and Master Volume down as you power on the amp. Keep holding them both down until you see the LEDs around the Master Volume light up. For AMPLIFi FX100, turn the pedal off and press and hold both the 'Tap' and Master Volume down as you power on the pedal. Keep holding them both down until you see the display light up with '01'. Next, on your iOS device, make sure that the AMPLIFi Remote app is fully closed by double tapping on the home button and swiping up across the AMPLIFi Remote app. Than within your iOS device Bluetooth settings you will need to 'forget' any entries for AMPLIFi, by tapping the 'i' to the right of any AMPLIFi entry and than tapping 'Forget this device'. Than press and hold the Bluetooth button on the AMPLIFi for 2 seconds until it begins to flash. It should than shortly appear within your iOS device Bluetooth settings, tap on it to re-pair. Than try again to launch AMPLIFi Remote app, tap the menu button located in the upper left of the app and look to see if it shows that your AMPLIFi is 'connected' or not. If your AMPLIFi is detected by the AMPLIFi Remote app, the next thing to do is to apply the available firmware update using the instructions found at the link below: http://line6.com/sup...ifirmwareupdate

If two XD-V55 receivers are connected via the antenna splitter kit and the receivers are powered on individually, the receiver that is powered on second will not initiate. The receivers must be powered on simultaneously to work. The antenna splitter kit requires the two SMA MALE to BNC MALE cables that the XD-V55 rackmount kit provides. As such, it is assumed that the receivers are rackmounted AND powered by a power strip.