Search the Community
Showing results for tags 'hd300'.
-
I was able to use the Line 6 Monkey v1.77 and after installing the driver still it show's, no driver was installed. I hope someone can help me here. I already reviewed other forums. I am currently using Win 10 64 bit. Dell Optiplex 9020 with i5 4th Gen processor. 4 GB RAM -
Ok here's what happens, just bought this HD300 and it's not recognized by my 2 computers. Installed monkey, drivers, and it installs as unknown device. If I go in the driver properties, I see Mbox instead of Line 6 Pod hd300. I manually switch it to the correct one and it's still not detected by monkey or hd300 edit.Ok here's what happens, just bought this HD300 and it's not recognized by my 2 computers. Installed monkey, drivers, and it installs as unknown device. If I go in the driver properties, I see Mbox instead of Line 6 Pod hd300. I manually switch it to the correct one and it's still not detected by monkey or hd300 edit. I'm on windows 8 64-bit. Tried multiple usb plugs: usb 2.0, 3.0, 2.0 with speed charging. Always the same. Also tried multiple versions of monkey and the driver, always from a clean install. Nothing. Here's what I get, seems monkey never sees the driver installed even though I see it in device manager. I also have a ticket open and didn't get a reply for a week now... Here it is: Pod HD300 Firmware 1.10 Connecting through USB to 2 different computer with Windows 8 64-bit, latest drivers and monkey. Not recognized. Driver is being installed as Unknown Device. If I go check the properties, it says the unknown device has the driver of a Digidesign Mbox. When manually changing the driver, it doesn't go through. Tried reverting to previous drivers and monkey, still not detected in Monkey. This is on both computers. Help please! thank you
-
Pod HD300/HD400 Factory Reset: Hold down the A footswitch while powering the unit on. Press the PRESETS knob, then press it again. Video Tutorial No Global Settings reset Pod HD/HD500/HD500x/HD Pro/HD ProX Global Settings Reset: Run Line 6 Monkey with the HD500X connected via USB. Highlight FLASH MEMORY and click REINSTALL LATEST (or INSTALL LATEST if Monkey shows that you are running older firmware). Make sure to back up all of your presets and setlists beforehand using the HD Edit software. Factory Reset: You must reinstall the firmware, when Monkey prompts you if you want to keep your existing presets, hit no. Video Tutorial Safe/Pedal Calibration Mode: Hold down the right arrow on the navigation button while powering the unit.
-
Hello everyone! My Line 6 Monkey doesn't recognize my pod hd 300 anymore. I've updated it at the last version but it keeps telling me that drivers are not installed. Instead I've installed them successfully more than once but Monkey still doesn't report them as installed, as a result my pod is not recognized. I've already tried disabling the SmartScreen filter for the download but the result is the same. it's not a matter of downloading or istallation because they go both fine. Does anybody could have had the same troubles or could know how to do to make it works? I am desperate :( ... Here a screenshot about it, it doesn't report drivers as installed even if I did it successfully
-
Forgive me if this has been answered a million times already, but I'm having trouble getting a straight answer. I have a POD HD300 and want to know if I can use two effects from the FX1 category. For example, if I want to use the Blue Compressor and the Tube Screamer clone for a patch, is there a way to make use of both of them? Am I stuck using either the compressor or the overdrive effect? Thanks!
-
Hi All I can't work out how to access the additional amp models in the HD300 (beyond the 16 available from the Amp Model Select Knob). I have gone into edit mode but cannot see how to access these additional amp models. And unfortunately the advanced guide does not tell you how to access them either. Thanks for any advice.
-
I am trying to layer 4 guitar tracks, 2 hard left and right and 2 not so hard left and right. I have noticed when I double up on tracks and lets say they are both centered or both in the left or right they sound weird. They sound like there is a flange on them or some sort of modulation effect. I figured it might have to do with phase but even that seems odd. I am forced to pan only 2 tracks hard left and right or my guitar tracks sound very weird. Anyone know what is going on? I might just stick to modeling guitar amps with VST plugins instead as I did not have that issue using those. Thank you!
-
I've written this several times but no one has ever given me a decent reason of why they (Line 6 Tech folks) can't fix this. Either the HD300 or HD400 are so old that they figure it's not worth changing, or someone has provided excellent instructions on how to incorporate both drivers or other SW/Firmware fix...so everyone else is good to go. So here's my problem. You go to the customtone page to filter for HD400 tones only - but...it seems that 70% of the tones are HD300 which I can't hear on my HD400. How hard is it to either actually provide a filter that works or at least show next to the picture of the unit that it's the HD300 vs the 400. Again, some guy named silverfish tried to educate me on how to do some work-around where I'd be able to use the HD300 patches on my HD400...but I wasn't able to get it done. As stated earlier, I've complained about this before - but it must be a low % issue - because I've never had a decent response from anyone except that silverfish dude.
-
I have the HD400 - I notice that ~80% of the downloads have the HD300. This happens even after I filter by only the "HD400" Do I need to download drivers for the HD300 in order to be able to use patches from the HD300 on my HD400? Is that even possible? Sure seems like as you move up the food chain/model # - that Line 6 would've built in the capacity to absorb older systems within the newer models? Also as a suggestion to the web designers, since the filtering doesn't appear to work, instead of showing a picture of the unit (HD300/DH400) why not just list which device it is rather than us having to hover over the unit to see what it is? Really appreciate any response to this.
-
Just installed the line 6 monkey on my new computer to try and record some more and before I did anything I had to install the Line 6 drivers v4.2.7.6 installers, Line 6 v1.72 installer and the POD HD300 edit v2.02 and during the installation of one of those my studio monitors cut out, I tried restarting my computer and even tried getting audio out of just my computer and other speakers and I'm not getting any audio at all and I don't know what the lollipop is going on. help??
-
Good morning, I ask you please to help me. I have a problem with the HD300 pod usb downloading the driver on pc tells me that the device is unknown and I can not connect it to your PC. I have already reset the pod 300. by starting the installation of the drivers from the .exe at one point he tells you that you should see a screen when connect usb HD300 pod asking you to force the installation of the driver for compatibility. to me this pop up, this screen does not open, so I follow the procedure that tells me that the drivers are installed. Also at the beginning when I linked the pod HD300 in the indication of the USB port and features I could see that the manufacturer was line6 that the door was appointed instead HD300 and now unknown device. please give me a hand thanks
-
Hi everyone! I happily joined the Line6 club recently and I am really surprised by the sounds I can get from my HD300 unit, but recently I started to have problems with the switches, nobody changed something in it hardware-wise, everything is factory-like. It's easier to show you in a video what's the problem so: I found out that by holding the A switch you enter in a button test mode "P16 TEST MODE", the screen shows "Knob ExtPdl" or "Knob IntPdl" and whatever I push it just jumps back at that and their value keep changing random. After a few days the problem got worse, now there are some LEDs that light up togheter with others, like the green tremolo light when the orange delay is on, and they sometimes flicker together with the tap LED. It's just like everything is short circuiting. I don't know if there is an authorized service in Romania so I could send them the unit.
-
Most of my patches are saved with the basic amp and reverb settings switched on, but with overdrive, a modulation effect and delay set up but switched off. So when I'm playing I'll switch those on as needed. The next time I use the patch, I want it to be in its saved state, with the overdrive, modulation and delay effects switched off. However the HD300 keeps them switched in, even if I select another patch and go back to the original one, it still has the variations switched on. Is there any way using the footswitches to recall a patch with its settings as they were saved?
-
First time messing with the HD Edit software, trying to create a patch with a harmonizer. But I want the harmony to be a half step, to achieve an affect similar to what you would hear in a Tony Danza Tap Dance Extravaganza song. I assume the effect I would use would be the frequency shifter, but how would I set it to get a half step harmony?
-
I recently picked up an HD300 from a guy online. I absolutely love the versatility. One thing I can't seem to find are the delay tap settings for dotted eighths. I know this was an item of contention a few years ago. Has this been addressed in a recent firmware update or am I just dumb and missing it in the settings? I'm up to (i think) v2.3 Fear not, I can always loop in my Line6 EchoPark but I was hoping I wouldn't have to. *wink wink nudge nudge*
-
Hey there. About to buy a used DT25, but not sure about the control POD. Like to use all this for practice and hopefully on stage once I'm familiar w it. Currently I use a VETTA HD. I also do not know much about MIDI. So please apologize any stupid kind of questions. ;.-)) 1. Most tutorials talk about a setup w the HD500 only - but this is too expensive for me. I understand you can control the amp in the same way w an HD300 ? Just w less memory resp. channels/presets for storing ? Or would there anything not available w HD300 vs. HD500 ? 2. Can I use only the effects of the HD300 w the pure sound of the amp ? 3. Dto. w no cabinet modelling ? 4. Is there a control over the effect routing ? Meaning Delay, Reverb, Modulation in serial/parallel effects loop between pre- and power-tube amp. But the boosters in front of the pre-amp ? 6. Dto. reg. the volume pedal ? Before pre-amp (for overdrive control) vs. after pre-amp for master resp. channel volume control ? 5. The HD300 is also able to control two DT amps like the HD500 ? 6. Read a lot about software verions upgrades to 2.x What would be the benefit ? 7. How can it be upgraded ? Via Windows PC ? And you would need a MIDI interface at the PC ? 8. Is it possible to have the same amp controls w a std. MIDI pedal where you can save settings and recall them ? Lots of questions. Sorry. ;-)) If I completely miss or mix the principals of the amp, I'm sorry, but let me know then as well. Many THX and Cheers from Munich, Germany. Gerhard.
-
Hello. I've been trying to fix my real bad tone issue for months now. I had a good tone and everything right up untill i had a rehearsal with a new guitar player in my band. When i brought my POD there everything went downhill, it sounded like **** and i have no idea what could've caused it. I figured it might've been the amp but i came back home and i had fuzzy sounds all of a sudden. I really hope it's not broken or damaged by any way and so turned to options such as updating my firmware and such.. and ofcourse, nothing. I attempted to do something about it today aswell (i am really depressed with what i am stuck with right now) and saw that my flash memory is not installed (shows - ). HOWEVER to make things more worse I can't update it. It shows a question mark and wont allow me to install it. After a while i somehow got it fixed, but the tone is still horrible and can't get ANYTHING decent out of it, even from downloading custom tones. So here is what i've done : resest to factory settings, reinstalled firmware and flash memory, download other tunes.. and im losing options. Some things i know what i can try to do is reinstall podhd300 driver completly, but other than that I am posting this so i can get other suggestions aswell, as im really frustrated with this issue. Many thanks ahead
-
HELP: Is there any way I can reformat the system in my Line6 HD300 I bought a faulty Line6 HD300 (Blank Screen but with power) Apparently this thing got broken when updating the HD300 (The internet connection got cut out while in the middle of the updating process) Is there any way I can reformat the system. Thank you! :D -
Hi everybody, I'd like to know if it's possible to sync my POD HD 300 to a BOSS RC-300 via a "USB to MIDI" cable... The goal would be to create a loop on the RC300 and then to have the delay tempo of the hd300 automatically synchronized with it. Has anyone tried that kind of connection? Thanks
-
Hello Recently I got a POD HD300 and I can't seem to get ahold of a decent tone for my 6string baritone tuned to Drop E. It's really muddy and undefined,I want a more digital tone,similar to Meshuggah-Tony Danza Tap Dance Extravaganza-Periphery etc. I have a .85 for a low E with on a 27,2'' with an EMG 81. A good example of what I'm after(or similar) is this https://soundcloud.com/thelivingdoorway/frederipoff-thordendal Any preset/info will be gladly appreciated. Thanks a ton and happy new year John
-
Greetings, I have owned a POD HD300 for six months and I think it's an okay piece of gear for me. However there are some practical issues which come up constantly. One major problem I've been having is the bank up/down feature when (accidentally) pressing the two footswitches at once. Is there a way to disable this feature altogether? I seem to be messing up my banks all the time since the footswitches are so sensitive and close to each other. It is very annoying, especially when playing live. As a sidenote, the sensitivity of the footswitches also comes up for instance while recording loops. Sometimes when I press the record switch, it just records a few ms of noise and starts looping that instead of turning the recording on. This is also an issue when changing between the modes, since pressing the footswitch sometimes jumps over a mode as it would have been pressed twice. Is there a way to make the footswitches less responsive in this manner? Regards, Juho
-
Hi! I own a Pod UX and I've purchased the Metal Pack addon. Today, i've bought a used Pod HD300 and I wondered if the Metal Pack Addon I've purchased earlier could be inserter in my Pod300. I've tried but it doesn't seem to be seeing it in any way. Must I buy it again for my HD300, or is there something to do to make it work? If it can be of any help, on the Line 6 webpage, on the "Autorised" page, my UX is detected, as well as my computer, but the HD300 isn't, even thought i've downloaded EzMonkey (which autorised my HD300 and allowed me the updates). Thanks in advance for your help.
-
Hi, I just bought a Pod HD300 and, when I use in in "stompbox" mode, while the AMP, FX1 and FX2 switches work as they should, the FX3 switch acts funny. When pressed, it not only activates the FX3 assigned effect, it also activates FX1 and 2 at the same time. I've updated the firmware and the flash memory but nothing happened. Did someone else run into this problem too?
-
Over on the Ideas page I posted this; A possible solution to expand existing units and provide us with all the functionality we are requesting. Please contribute any ideas you have for such a device. Think as big as you like! http://line6.ideascale.com/a/dtd/POD-HD-ULTIMATE-Module/502816-23508
